- #Best control surface for logic pro x 2020 for free
- #Best control surface for logic pro x 2020 software
IT IS THEREFORE IMPORTANT THAT YOU READ THIS LICENSING AGREEMENT WITH CARE BEFORE USING THE SOFTWARE. BY USING (INSTALLING OR MAKING A BACKUP COPY OF) THE SOFTWARE, YOU ARE AGREEING TO THE TERMS SET OUT IN THIS AGREEMENT.
#Best control surface for logic pro x 2020 software
THE ENCLOSED SOFTWARE PROGRAM IS LICENSED BY KORG TO YOU AS THE ORIGINAL PURCHASER FOR USE ONLY ON THE TERMS SET OUT HEREIN. (REFERRED TO IN THIS AGREEMENT AS “KORG”) FOR YOUR USE OF THE SOFTWARE IN THIS PRODUCT AND OUR SUPPORT SERVICES TO YOU. THE FOLLOWING IS THE SOFTWARE LICENSING AGREEMENT BETWEEN YOU, THE END USER, (REFERRED TO IN THIS AGREEMENT AS “YOU” OR “YOUR”) AND KORG INC. Mackie MCU is a protocol that uses MIDI so probably would be best to understand MIDI first.SOFTWARE LICENSING AGREEMENTPLEASE READ THIS CAREFULLY BEFORE YOU OPEN THE DISK PACKAGE. There is MIDI section at the end that details the Mackie protocol MIDI messages. I can’t remember the exact name of the document but I believe it was published by Logic control.
There are several examples of each type in various places on the forum, so you could probably search for them and develop your own solution or send me an email and with your spec, I can provide an estimate and build something for you.įor Mackie MCU protocol which describes the messages used specific for this protocol, do a web search on “Mackie MCU protocol”. This can all be done but a complete solution is a paid service. For V-Pots probably V-Select for push and then determine where you want Track-up, Track-down, Bank-Up, Bank Down, the mutes, solos, etc. If I remember it is CC 0x30-0x37 on MIDI CH1 with values of 0-13 so you would need to scale 0-13 up to 0-127.Īs to buttons, it would be dependent on the push encoders and what banks of the MFT you want to use for what purpose.
For reverse translation (LED display, I believe the the mapping is a bit more complicated. Each track has it’s own MIDI CHįor V-POTS, I recommend setting twister knobs for ENC 3F/41 and then set up to convert to Mackie VPOT where values are 01 02 03 for right movement and values are 0x41 0x42 and 0x43 for left movement CCs are 16-23 (0x10-0x17). There would be reverse translation coming back from Logic Pro. and what CC's you want them assigned on your MFT.įor Faders, I recommend setting your twister knobs for CC and then convert from CC to Pitch Bend. So I recommend you set the first 8 encoders as 3F/41 and the remaining as absolute. Typically you do not see movement that far howver usually just 1-5 and 64-69. Forward direction is value 1-63 and reverse direction is 64-127. For values I use the CC value for both MSB and LSB of the fader.įor VPOT's it is best to set you encoders for relative 3E/41 and convert from there. If you want paid, services, just drop me an email.īut I'll tell you Mackie MCU uses pitch bend for faders with tracks 1-8 equal to MIDI CH 1-8 and master fader as pitch bend on MIDI CH 9. Reach out to me when you get your MIDI fighter twister here. After that it is up to you what you want what push buttons to do what function. I then use the last knob so I can push and make it a master fader. Generally I like the first 8 as V-POTs with push and the 2nd 8 as faders. I can probably help you map at least your first 16 knobs for your. Independent Bome when you know what knobs you want to map to what.
#Best control surface for logic pro x 2020 for free
I'm a paid consultant for complete solutions but help out with Bome related user questions and general support here for free (up to a point). Here is a link of controllers I've been able to emulate MCU protocol and other paid consulting services I've done for extended capabilities using Bome MIDI Translator Pro. I'm not sure what controllers Logic Pro supports besides Mackie Control Universal Protocol (MCU), however I've mapped several controllers to emulatate MCU with success so although it might or might not work out of the box with Logic Pro, I know with the Bome Software and some knowledge of how MCU works, you can get it to work, so it is really a matter of cost and/or time investment on your part. The encoders and switches are mostly all mappable. I haven't had any experience with Logic Pro but I have a MIDI Fighter Twister and it is a fine controller.
0 kommentar(er)
